Xbox 360 Lite-On DG16D2S Extract Key

In later August 2008 a method to dump the new Lite-On DG16D2S drive was released. It requires a serial controller and SATA controller to dump the key.

Thanks goes to Geremia, C4eva, Tiros, Schtrom, TMF, Redline99, and the Xbox-hacker community.

Lite-On DG16D2S

This drive started to appear in machines manufactured after 20th April 2008 (2008-04-20). Currently it's not possible to dump or flash the drive, only extracting the key.

Serial Adapter

The serial adapter will be connected to the Lite-On drive board and used to interface with the MT1319L controller using the DVDKey utility (more below).

Build

Either buy a pre-built RS-232 adapter or build one yourself. The parts are cheap and it isn't hard to build.

Some RS-232 transecivers:

MAX3232
ST3232

Here is my adapter based on a MAX3232 chip:

To verify that the serial adapter works, make sure the serial-port is enabled in the BIOS, and join (loop) the Tx and Rx pins together (pin 2 and 3). Open HyperTerm (or any other terminal applications) and try the default settings (9600, 8, None, 1). Type something in the terminal, it should echo back what you typed if it's working.

Alternatively, try this very simple RS-232 level converter. Composed of only resistors, diodes, transistors, and a capacitor.

Links:

Connect

Once the serial adapter is ready, connect the 3.3v, Ground, TxD and RxD points to the Lite-On drive board. There is also two jumpers/solder pads for TxD and RxD that needs to be joined. The points are shown below:

Download the original diagrams

The adapter installed:

Dump Preparation

Requirements

These are the basic requirements to connect the drive to a computer and powering it.

Native SATA controller or VIA VT6421A or VT6421L PCI card
Power to the Lite-On drive, either:
- Team Xecuter Connectivity kit v1 or v2
- The Xbox 360 located close the computer to provide power

Utility

Download the DVDKey utility. The utility will interface with the drive over the serial connection and dump the key via SATA.

Download DVDKey v1.1

Create a DOS boot disk and put DVDKey on the drive.

Find SATA Port

DVDKey requires the address of the SATA port where the Lite-On drive will be connected. The address location is in HEX format (e.g. 0xA000 or A000).

Currently there are 3 different methods to find the address, some easier than others.

iPrep

This is a Windows tool to create a boot disk for iXtreme flashing.

Download iPrep 101 v0.0.6.2 beta

Install the application and open it, in the middle of the window, look for the name of your SATA controller, click the question mark on the right-side, the SATA port is the first 4 (four) characters in the DeviceIO string. Here it's A000.

Make sure you have the .Net Framework v2.0 installed if the application throws an error on launch.

DosFlash

DosFlash is used to flash BenQ drives (and Toshiba-Samsung drives). It will report the address of the detected drive before it continues.

Download DosFlash v1.4 beta

Connect the Lite-On drive to the SATA port, create a DOS boot disk and put DosFlash in it, boot to DOS, and execute dosflash.exe in the Dosflash16 directory (DOSFLA~1). Press n on any prompts. The port will be reported in the text string starting with MTK Vendor Intro failed on port.... Press ctrl+c to exit.

The output should look like this:

c:\DOSFLASH\DOSFLA~1>dosflash
DOSFLASH V1.4 Beta Build 20071115 by Team Modfreakz and Kai Schtrom
 0) 0x01F0 IDE    Pri Master   None
 1) 0x01F0 IDE    Pri Slave    None
 2) 0x0170 IDE    Sec Master  None
 3) 0x0170 IDE    Sec Slave   None
MTK Vendor Intro failed on port 0xA000. If you choose to resend the command
you should turn the drive off and on after you pressed "Yes".
Do you want to resend the command until the drive responds (Y/N)? n
4) 0xA000 SATA   Pri Master   ATAPI PLDS   DG16D2S 74850C
     Flash ManufacturerID: 0x00, DeviceID: 0x00
     Flash Type: MTK Vendor Intro failed!
     Flash Size: 0 bytes (0 KB)
5) 0xA400 SATA   Pri Master   None
6) 0xA800 IDE     Pri Master  None
7) 0xA800 IDE     Pri Slave   None

Enter the number of an ATAPI drive to read, write, erase flash:
c:\DOSFLASH\DOSFLA~1>

Picture:

Slax Linux

Slax is a Linux distribution tweaked for Xbox 360 use. It will put the Hitachi-LG drive in mode-b for flashing.

Download Slax Linux 2.1

Connect the Lite-On drive to the SATA port, burn the image to a CD-R/DVD-R, boot the disc, eject the tray if the boot halts, and login using username root and password toor.

Type dmesg|grep SATA' (case important, SATA)' to filter out the SATA messages from the kernel boot log. The SATA port address can be found after SATA max UDMA/133 cmd, before ctl. In this example 0xA000, or A000 is the part that will be used here.

The output should look similar to the below:

root@slax:~# dmesg|grep SATA
ata1: SATA max UDMA/133 cmd 0xA000 ctl 0xA00A bmdma 0xB000 irq 11
ata2: SATA max UDMA/133 cmd 0xA400 ctl 0xA40A bmdma 0xB008 irq 8

Picture:

Dump Key

Once the steps above is complete, the dump process can begin.

Half Open Tray

The tray has to stay half open during the process. Once the drive tray is half-open it will stay open, not close on the next power up as a normal drive would do.

Note: On some setups it's not needed to have the tray half-open, it works fine with the tray closed.

Eject button method

Power on the drive
Press the eject button - On the Connectivity Kit or front of the Xbox 360
Remove the power again
Manually press the drive half-way in

Paper clip method

Locate the black slider on the right-side on the bottom of the drive (see picture)
Use a paper clip or screwdriver to press the slider all the way in
The tray should slide or pop out, pull it half-way open

Dumping Procedure

Follow this procedure to dump the key:

Power off the computer
Disconnect power and SATA cable on the Lite-On drive
Connect the serial controller cable to COM1 (bios setting 3F8/IRQ4) on the computer
Connect power to the Lite-On drive
Power on the computer
Boot to DOS, either from hard drive or a flash drive, DVDKey already installed
Plug in the SATA cable to the Lite-On drive
- Note: On some computers (VT6421), the cable can be plugged in before the computer is powered on
Execute DVDKey with the SATA port address (found above) as an argument:
- dvdkey a000
After 20-30 seconds the key will be dumped
If it fails, try again from step 1

The output should be something like this:

c:\DVDKEY>dvdkey a000
Port A000
Drive Present
Wait about 20 seconds

GOT SOMETHING !!!    sona: 03   sega: 54
DVD key:
9174C2D5905AE8B9ACB23CD116XXXXXX
Seems a GOOD Key!!!!
KEY.BIN saved

PLDS   DG-16D2S      74850C
INQUIRY.BIN saved

PLDS   DG-16D2S
IDENTIFY.BIN saved

c:\DVDKEY>

Picture:

Errors

If you got something like this, you need to:

Power down the drive between each tries
Check the serial adapter communication
Wrong COM port selected for the serial adapter (DVDKey hardcoded to COM1)

c:\DVDKEY>dvdkey a000
Port A000
Drive Present
Wait about 20 seconds

It didn't work, sorry   reg1: 54
DVD key:
00000000000000000000000000000000
Seems NOT a good DVD Key!!! 00 00
KEY.BIN saved


c:\DVDKEY>

In this case the wrong SATA port address is used. Try iPrep, DOSFlash, or Slax to find the correct port.

c:\DVDKEY>dvdkey a400
Port A000
Problems with sata status, try to reboot PC 

c:\DVDKEY>

Spoof Drive

The Xbox 360 system is married to the specific DVD drive when it ships from the factory. Two parts in the DVD firmware is linking it to the 360, the first is the DVD encryption key, e.g. 9174C2D5905AE8B9ACB23CD116XXXXXX, and the second is the drive identity, e.g. PLDS DG-16D2S 74850CA0A1D608CG81881200VM1.

For any games to start at all the key stored in the NAND flash has to match the key in the firmware on DVD drive, else only DVD movies will play.

Earlier drives (Toshiba-Samsung, Hitachi-LG, and BenQ) had the same drive identification string, but the new Lite-On has an unique identifier per drive. This unique identifier is found in the INQUIRY.BIN file.

DVD Key

Have your hacked firmware for the drive you want to use as a replacement for the Lite-On ready. The hacked firmware is found in Benq iXtreme v1.41 for BenQ, Samsung.iXtreme.1.4 for Thoshiba-Samsung, and 360FW-Toolbox-v4.8 or iXtreme1.4_Hitachi for Hitachi-LG.

If you haven't written down the key for the Lite-On during the dump process, download Tiny Hexer and open the KEY.BIN file. The key is in HEX form, here it's starting 9174....

Write down this key and save it to a text file for later reference and backup.

360 Firmware Toolbox (recommended method)

Download and extract 360 Firmware Toolbox v4.8 or newer.

Download 360 Firmware Toolbox v4.8

Open 360 Firmware Toolbox, select File and Open, and find the hacked firmware for the new drive. Copy the Lite-On DVD key found above and paste it into the Key field under the Key Information section. Click Save Key to apply the change.

The key is now patched. Next, spoof the drive identification.

Manual method

The key location is different for each drive and firmware version. Use the table below to find the correct location.

BenQ

BenQ key string is located at 0xE030 to 0xE040, length 0x10 bytes.

Toshiba-Samsung

Toshiba-Samsung key string is located at 0x401A to 0x402A, length 0x10 bytes.

And alternatively 0x40EC to 0x40FC, length 0x10 bytes.

And alternatively 0x4116 to 0x4126, length 0x10 bytes.

Essentially the key can be found by following this sequence [1]:

01 EE EE EE EE - 16 byte key location - 02 11 11 11 11 - 16 byte key location - 03 EE EE EE EE - 16 byte key location - etc

Hitachi-LG

Version 32 / 36 / 46 / 47 / 59

Hitachi-LG key string is located at 0x4F00 to 0x4F10, length 0x10 bytes.

Version 78 v1

Hitachi-LG key string is located at 0x4B00 to 0x4B10, length 0x10 bytes.

Version 78 v2

Hitachi-LG key string is located at 0x4C30 to 0x4C40, length 0x10 bytes.

Version 78 v3

Hitachi-LG key string is located at 0x4D20 to 0x4D30, length 0x10 bytes.

Version 78 v4

Hitachi-LG key string is located at 0x4E10 to 0x4E20, length 0x10 bytes.

Version 79 v1

Hitachi-LG key string is located at 0x4B00 to 0x4B10, length 0x10 bytes.

Version 79 v2

Hitachi-LG key string is located at 0x4E10 to 0x4E20, length 0x10 bytes.

Identification String

The identification string for the Lite-On drive is saved to the INQUIRY.BIN file. This file was created during the dumping process.

350 Firmware Toolbox (recommended method)

Download 360 Firmware Toolbox v4.8 or newer and exact it to a folder.

Download 360 Firmware Toolbox v4.8

Launch 360 Firmware Toolbox and open the hacked firmware for the new drive. Select Tools and Spoof Firmware. In the selection box pick Custom (Requires inquiry.bin) and click Apply Spoof.

In the next file dialog that's popping up, find and select the INQUIRY.BIN file from the Lite-On dump. This file includes the unique identifier for the drive. Click Ok and a message will report the change was made.

To verify and view the unique identifier, select Tools and Spoof Firmware again, and look at the top of window under Current Detection String. This is the real spoof string.

The firmware should now be ready and can be flashed back to the drive.

Utility to use:

BenQ: Use DosFlash
Toshiba-Samsung: Use DosFlash or MTKFlash
Hitachi-LG: Use 360 Firmware Toolbox

There are many good tutorials available that shows how to flash the different drives.

Manual method

Open the INQUIRY.BIN file in Tiny Hexer, select all the 6 lines (ctrl+a), and copy it (ctrl+c).

Next, open the hacked firmware and find the correct range to replace in the table below. The block starts with 0580 0032 .... The identification string is 0x60 bytes long. Mark this range and paste the Lite-On inquiry block into this selection.

BenQ

BenQ identification string is located at 0x2D5C to 0x2DBC, length 0x60 bytes.

Toshiba-Samsung

Toshiba-Samsung identification string is located at 0x20B0 to 0x2114, length 0x60 bytes.

Hitachi-LG

Version 32

Hitachi-LG identification string is located at 0x3D460 to 0x3D4C0, length 0x60 bytes.

No checksum reset.

Version 36

Hitachi-LG identification string is located at 0x3D444 to 0x3D4A4, length 0x60 bytes.

No checksum reset.

Version 46 and 47

Hitachi-LG identification string is located at 0x3D47C to 0x3D4DC, length 0x60 bytes.