T-Rex 250 Setup

From ivc wiki
Revision as of 16:04, 25 November 2011 by Ivc (talk | contribs) (→‎Gyro)
Jump to navigationJump to search

This shows the setup of my T-Rex 250 and the experience I've had learning and experimenting with the build. Please visit RC Heli Wiki for an excellent resource regarding helicopter terms and concepts.

Follow this guide to-to-bottom, get a good mechanical setup before setting up the electronics. A great companion is Bob White a.k.a Finless' videos.

Pre-requisites

Follow the manual to setup the basic build and then use these steps to do the finer adjustments. The virtue of this setup should be to make the most adjustments as precise as possible. Any sloppy or oblique leveling will have an adverse affect later on.

The two main helicopter control configurations are Mode 1 and Mode 2, the latter has been adopted by most people. I use Mode 2 in the configurations below.

Helicopter control configurations.png

Blades

Grip

The right amount grip on the blades can be tested by gently hitting the leading edge of the blades with your finger they should fold back about 45 degrees. If they fold all the way back and bind with the blade grip then they're too loose. The blades will swing back and forth in FFF due to airspeed differences between the advancing and retreating blades. This is normal but having a little bit of friction helps to dampen it and make a smoother flight. However you need to make sure both blades blade bolts are tightened the same amount.

Balancing

Correct blade balancing and blade weight will reduce vibration and stabilize the helicopter. It's an essential part of the setup. Make sure the surface you're performing the balancing is perfectly level.

Balancing the blades on a T-Rex 250 is not really necessary, but it's a good practice to check the blades anyway.

A good way to balance the blades consist of a two part method:

  1. Find the center of mass (or center of gravity) of each blade by applying trim tape to the end of the lighter blade
  2. Then, use a blade balancer to apply trim tape to center of mass mark on the ligher blade until they're level

The video linked below shows the procedure.

Tracking

Bad tracking is caused by one blade tracking a little higher or lower than the other. By marking each blade with contrasting tape it's possible to see which one need adjustment.

The tracking can be fixed by lengthen or shortening the link holding the main rotor spindle. Only do adjustment by one whole turn at a time. If a half turn is needed, don't turn the link a half a turn but go to the link one step down on the Bell Hiller level arms. These arms will have more range and will give the rotor spindle more gradual control.

Also make sure none of the following are bent or broken:

  • Identical link length (as described above)
  • Main shaft
  • Feathering shaft
  • Blade holder arms
  • Head dampeners

On the T-Rex 250, for me, when using carbon fiber rotor blades, the difference between absolute tracking and a little off is like a dull razor-blade and a brand new one. The heli stabilizes and is more robust in the air when the blades are tracking properly. Do a half-turn on the wash-to-benhiller link to dial it it (even if the A is facing inwards).

References:

Flybar

The flybar is working as a mechanical gyro, smoothing and stabilizing the heli when in horizontal plane, e.g. hover.

References:

Servos

Try to weight balance the helicopter putting the tail servo tilting to the left and the elevator servo pointing right. This will improve the center of gravity (CG).

Main gear hit

A build tip to avoid having the servo arm hit the main gear on the left side, is to swap the aileron and pitch servos. Then the servo arm on the left side will not have a steep angle against the holes in the main gear. When swapped, the arm will point in the same direction as the main gear rotation. If it hits, it won't get stuck.

The elevator servo should be installed on the inside of the frame, with the main mounts on the inside and the body sticking outwards.

Loosening link arm

The linkage ball and link rod fit is usually pretty tight and light force is needed to move the link rod. When moving the link rod around the ball, the movement should require just a tiny bit of force and move almost freely. It's to free when the link rod dangles, it should move free enough that a slight air blow would move the rod and instantly stop. Use a appropriately sized ball link re-sizer tool to do a few revolutions between each try to find the perfect fit.

Receiver

AR6100e receiver setup (RECEIVER - Device):

  • THRO - ESC
  • AILE - Right cyclic servo
  • ELE - Rear cyclic servo
  • RUD - Gyro (3-wires plug)
  • GEAR - Gyro (1 wire plug - gain)
  • AUX1 - Left cyclic servo

Other receivers will have different layout.

Radio

Create a new profile for the helicopter and reset all the settings. Make sure there are zero trim, zero sub-trim, revo-mix turned off, 50/50/50% swash mix, diagonal pitch and throttle curve, and other settings default or at their suitable values.

On a Spektrum transmitter, bind the transmitter and receiver using the bind plug and set the fail-safe state to low-throttle and throttle-hold switched on. This will essentially prepare for a soft landing by cutting the power and increase the blade pitch if the transmitter signal is unexpectedly lost. Also re-bind the Rx when the heli is set-up.

Watch the beginning of Finless CCPM setup to get a good start.

When dealing the RC helicopters, always remember to power on the radio first then the receiver and power to the engine, reverse the rutine to disconnect. The helicopter could spin-up unexpectedly if the receiver doesn't have contact with the radio. Low throttle stick and throttle hold is also important before flight.

Head

The head setup should mechanically be as symmetrical and zero-pitched as possible. The radio should have a straight pitch curve (0-50-100) in normal mode before starting the adjustments.

This is only the mechanical build, the tweaking is mentioned below. Install the servos and mount a suitable servo arm 90 degrees to the swashplate. Connect the rods to the swashplate with the length specified in the manual.

Figuring out the correct direction of the swash servos is a two step process. Move the throttle stick slightly up and watch the servos, all three should move collectively up to raise the swashplate, if one servo goes in the opposite dirrection go into the radio setup and reverse the direction of the affected servo. Alternatively if the swashplate is moving down while the stick is moving up, go into the swash mix and invert the pitch value, from positive to negative. Do the same for aileron and elevator.

The head is split up in 3 levels, from top-to-bottom; Bell-Hiller/Seesaw mixer level, washout arms level, and the swashplate level (look at the picture below). On zero-pitch the Bell-Hiller/Seesaw and washout is level. That's determined by the lengths of the link-rods connecting to the arms. Both arms should be identical length for each level. The washout arms should be positioned in the middle of the shaft for maximum and minimum pitch travel when moving throttle stick.

Helicopter head1.jpg Helicopter head2.jpg

If everything seem level, use a digital caliper verify and duplicate the length of related link rods. This will reduce vibrations and tracking issues.

CCPM - Collective Cyclic Pitch Mixing

Final CCPM setup:

  • 3 servo 120° degrees apart
  • Swash mix (will differ from model-to-model):
    • Aileron: -30%
    • Elevation: +35%
    • Pitch: +40%
    • No exponential
  • Maximum/Minimum blade pitch: 11.0°
  • Aileron/Elevation blade pitch: 6.0°

This is a compact summary of RC Heli Wiki and Bob Finless White videos, please refer to those for details.

The Collective Cyclic Pitch (CCPM) mixing controls the pitch and movement of the rotor and flybar, thus lift pitch (up/down), aileron movement (left/right), and elevation movement (forward/backward). It's called collective because there are 3 servos involved. There are two types of CCPM, mechanical bell crank and electronic mixing. The latter one is used on most helicopters today but requires precision servo setup and radio configuration. The radio is setup to mix, or compute the values, for the 3 servos in order to move the swashplate in the right direction and plane. Be it up-down, left-right, or forward-backward. It's imperative that the head is precisely setup mechanically to get a good CCPM configuration.

First check if the servos are going in the right direction, if one servo goes in the opposite direction, reverse that channel. Alternatively, if you move aileron left, but the swashplate moves right, go into the swash mixing, change the positive aileron percentage to negative value to reverse the movement.

Swash mixing controls the pitch of the blades. A pitch gauge is mounted on the main blades and is used to measure a predetermined pitch against the level flybar. The higher the value, the steeper the pitch. A regular setup usually use collective pitch 10.0° or 11.0° (lift) , higher for more flexibility. The maximum and minimum pitch should never bind and lock the servos. Aileron and elevator pitch is normally 6.0° (navigation).

After the process below is done, everything should be level and swash mixing complete, the movement of the collective pitch to maximum or minimum should keep the swashplate level. But it's not always true if the servos move in different speed or travel range. This issue is called CCPM interaction and can be handled by watching the flybar at aileron and elevator position (side, front) while moving the pitch up and down. Use travel adjust (not sub-trim) to counter the reaction and dial in the appropriate servo travel to keep the swashplate level for the full top to bottom range.

These are my notes when I first set up the head:

  1. Disconnect 3 engine plugs, allows pitch stick movement without spinning up rotor
  2. Pitch curve 0-25-50-75-100%, throttle center stick (use Tx monitor), zero trim, zero subtrim, 50-50-50% swash mix
  3. Find best horizontal servo arm/horn, try rotating horn 180° to see if it will be more level
  4. Sub-trim a few points to perfection, <20, 100% horizontal arm, center stick
  5. Add swash-plate, use length of rods per manual
  6. Put on swash leveling tool, adjust rod length for large gaps and use sub-trim to level swash to perfection, put head back on
  7. Test maximum washout travel up to the beginning of the head and minimum swash-plate travel down against the shaft lock-disk, adjust rods to fit swash+washout in the middle of the shaft, e.g. one (or more) turns on all 3 rods up or down, swash should stay level, play around, test maximum throw e.g. low throttle+aileron/elevation
  8. Washout floats between swash-plate and flybar-cage, adjust flybar-cage rods to make washout and flybar level, rods should be identical length, but T-Rex 250 has fixed length, use sub-trim on all 3 servos to lower/heighten the swash-plate instead, will also affect main blade pitch
  9. Seezaw should be level, hold flybar 100% horizontal level and measure against, adjust length on rods from swash-plate to seesaw, should be 100% identical length
  10. Same with main blade rods, level, identical length, but on T-Rex 250 fixed length, no adjustments needed
  11. CCPM interaction, two steps, place the heli left side facing you, turn flybar paddle also to the left side of the heli, adjust elevator servo travel at full and low throttle position. Go center-max-center-max back and forth and adjust the travel to level the paddle at maximum/minimum. Then turn the heli and flybar paddle 90°, now facing the front and paddle, and do the same for aileron servo travel, don't touch pitch servo travel
  12. An alternate method, remove the head as in step 6, place the swash leveling tool back on, first move the pitch to maximum, adjust the Elevator and Aileron travel so that there is no gap between any of the three legs, then move the pitch to minimum and do the same, this method is will give more accurate result
  13. Mount the pitch gauge, dial in pitch 11.0° positive and negative, move throttle stick to maximum/minimum and try to level pitch gauge against flybar by adjusting swash mix Pitch value, if positive and negative blade pitch doesn't match or is different, the washout is not 100% horizontal level, re-adjust from step #7 and forward
  14. Do the same for Aileron and Elevation swash mix, but center throttle stick, 6.0° positive and negative, move aileron/elevation stick to maximum/minimum and then adjust swash mix value, hard to get absolute, find middle point

Ended up these settings, these are for MY heli, yours will differ:

  • Swash mix: 3 Servos, 120degrees, Exp inh., Aile -30%, Elev +35%, Pit. +40%
  • Travel adjust: Thro: H100L100, Elev D94U100, Aile L109R103, Rudd L100R100, Gear +100-100, Aux2 +100-100, Pit. H100L100
  • Subtrim: Thro 0, Eleve U13, Ail L2, Rudd 0, Gear 0, Aux2 0, Pit. L10
  • Reversing sw: Ch 1Thro Nor, 2Aile Rev, 3Elev Nor, 4Rudd Rev, 5Gear Nor, 6Pit Nor, 7Aux2 Nor

References:

Pitch/Throttle curves

T-Rex 250 curves per manual:

  • Throttle Normal mode: 0-40-70-85-100% (now using 0-45-70-85-100)
  • Pitch Normal mode: 40-X-55-X-100% equals -2°, +X°, +4°, +X°, +11° blade pitch (now using 50-x-65-x-100)
  • Throttle Stunt1 / IdleUp 1 mode: 80-75-70-75-100%
  • Pitch Stunt1 / Idle-up 1 mode: 0-X-75-X-100% equals -11°, -X°, +5°, +11°
  • Throttle Stunt2 / IdleUp 2 mode: 100-X-90-X-100%
  • Pitch Stunt2 / IdleUp 2 mode: 0-25-50-75-100% equals -10, -X°, 0°, +X°, +11°

Throtle curves graphics from the T-Rex 250 manual:

Helicopter throttle trex250 normal.png Helicopter throttle trex250 stunt1.png Helicopter throttle trex250 stunt2.png

The idea behind pitch and throttle on one stick is to keep a constant headspeed. If the pitch is steep more engine power is required to keep the headspeed revolutions up. This is accomplished by setting up curves on the radio for controlling the pitch and throttle individually. There is usually a 5-point coordinate system to set the percentage at a specific stick position. Many, up to 3, curves can be used for different flight modes; hovering, stunt1/idleup1, and stunt2/idleup2.

Helicopter flightmode switch.jpg

On the radio there's a way to switch between Normal Mode (hovering), Stunt Mode 1 (3D), and Stunt Mode 2 (more power 3D). Stunt mode is also referred to as IdleUp 1 and IdleUp 2, while hovering is called Normal mode. A last mode is Throttle Hold for auto-rotation on engine failure, a second switch is normally used for this. Useful when battery is empty or when a crash is inevitable (less damage).

Helicopter throttlehold switch.jpg

Normal Mode is used during spin-up and hovering. With the stick down the engine will be off and with 70% up the helicopter should be hovering. These parameters are mainly set-up on the radio by altering the engine throttle and rotor pitch curve.

With Stunt Mode turned on the hovering mode is turned into a flexible mode where the helicopter can perform acrobatics and be flown a up-side-down. Essentially the Normal Mode above 50% is mirrored to the 0-49% section of the stick, but with a negative rotor pitch instead. Look at the picture below to understand the difference between Normal and Stunt.

While setting up the curves, there is an option to enable Exponential. Expo. will smoothen the curve and stick input will have a finer feel, not rough. More stick movement is required to get to the same servo movement. But it's not recommended to keep expo. on as it removes some of the real feel of the helicopter and can hinder progression in flight style.

Normal, hovering mode example (left throttle, right pitch):

Helicopter normalmode throttle.png Helicopter normalmode pitch.png

Idle Up, 3D stunt mode example (left throttle, right pitch):

Helicopter 3dmode throttle.png Helicopter 3dmode pitch.png

The throttle curve dips on the middle because the pitch is close to 0 degrees, thus requiring less power. Higher pitch requires more engine power to keep the headspeed constant.

The manual for the helicopter usually specifies suitable pitch and throttle curves.

Dual Rates

Dual Rates, as the name suggests, can be used to setup two different servo ranges to limit the maximum throw, or travel. This lowers the sensitivity and can be used to lower the sensitivity of the helicopter in flight (but requires more stick movement).

If the the dual rate is set to 80%, full stick input will move the servo arm 80% of the maximum range. Making dual rates useful for new users and hovering.

Tail

To keep the heli steady and stable in forward/backward/up/down flight it's essential to have a good mechanical tail setup. The T-Rex 250 had, and possibly still have, problems with the tail unexpected wagging/flickering mainly because of loose tail blade holders. The later kits and SE model has the 3rd revision of the tail blade holders and incorporate dual "chinese weights" on each side of the holders. These weights and the centrifugal force helps to eliminate the blade holders from flickering back and forth.

To mechanically set-up the tail:

  1. Center the tail servo by connecting it to the GYRO channel on the receiver and apply power
  2. Find a servo horn, preferably the round one, that is as close to perpendicular, 90°, to the boom
  3. Mount the link ball on the servo horn, 5 mm from the center (first hole), use CA glue to fasten it
  4. On the tail, move the control arm back and forth to find the middle point between the extreme points (max/min)
  5. Adjust the length of the link to be the exactly in the middle point
  6. Fasten all the screws with brushing to minimize slope, also properly fasten the the screws holding the blade grips

The pictures below illustrates the ideal setup.

Helicopter tailservo perpendicular.jpg Helicopter tail control arm middle.jpg Helicopter tail setup.png

Gyro

Helicopter gp750.jpg

GP750 settings (move rudder stick to left for Green and right for Red):

  • Pulse frame rate: 1520us - Green
  • Servo type: DS (Digital Servo) - Green
  • Servo direction: Reverse - Red
  • Servo travel adjustment: Limit set with rudder stick up to max but no binding
  • Heli type/delay: Small heli - Red - Delay: 0 (center rudder stick)

The gyro is a device connected between the receiver and the rudder servo, it will stabilize the tail by counter the torque reaction of the main rotor. There are two types, heading hold mode continuously tries to hold the tip of the helicopter at a constant angle, while the other mode, rate mode, dampens any external push to the tail. The former is preferred for normal hovering and acrobatics, while the second is mostly used for scale models.

On the AR6100e receiver the 3 wire plug from the gyro is connected to the RUD-channel and the single gain wire to the GEAR-channel.

Don't move the heli or touch the transmitter sticks when powering on the receiver and gyro. A green light will indicate heading hold mode and red rate mode (GP750).

Helicopter gp750 settings.jpg

Setup

Setup:

  • Round servo head (less flex)
  • 5 mm from servo center
  • Gyro Gain: 63% (19% real heading hold gain)

The gyro is connected to the receiver by two plugs. One for the rudder input and one for gain. Gyro gain is used to control how much the gyro tries to control the tail or hold authority and is measured in percentages. The range 0-49% is called rate mode (also called normal mode) and the tail will not automatically bounce back to the original position if it has been pushed by an external force, but rather dampen the movement. While the upper 51-100% range is called heading hold mode (also referred to as AHTCS) and will try to keep the front of the helicopter at a constant angle/heading regardless of external forces. Rudder stick input will notify the gyro and the gyro will then try as hard as it can to rotate, or move the tail, in the direction of the input. Dialing in the gyro gain is essential to get a stable tail.

Helicopter gyro gain.jpg

The intermittent range (0-50% and 50-100%) is used to fine tune the tail gain. If the tail wags back and forth the gain amount has to be reduced and if the heading isn't holding (pirouetting) the gain has to be increased.

Note that the gain wire is electronically connected like any regular servo and if the channel is reversed so will the rates. On most radios, the gyro mode can be setup at specific rates for different flight modes.

There are two ways to set gyro gain, either via the gyro menu or set the channel end points, a.k.a maximum/minimum travel range or adjustment. The former is preferred.

To find the true gyro gain use these equations:

  • When using end points/travel adjustment: (End point value) / 1.44
  • Or when using the (preferred) gyro sens menu: (Gyro value in radio - 50) * 1.44

A good default start value is around 32% gyro gain (72% in radio gyro mode). It's important to not use any sub-trim on the rudder and adjust the link rod instead, this will leave the gyro in command.

These are my notes when I first setup the tail:

  1. Zero sub trim, 50% gyro gain, no travel adjustments
  2. Find best horizontal servo arm
  3. Adjust link rod length for tail output shaft to be in middle of travel when center stick/servo
  4. Program gyro, set servo type, frame rate, reverse/normal (to be tested during first flight), servo maximum travel limit, helicopter type and delay
  5. On spektrum/jr, configure GEAR-channel to GYRO
  6. Go into Gyro Sense menu, adjust gyro percentage to 63%, which is 19% real gyro gain
  7. When heli is stationary and in heading hold mode, the servo will not reset position to center when stick is released, this is normal

Guides:

ESC - Electronic Speed Controller

Helicopter rce-bl15x.jpg

The default RCE-BL15X settings:

  • Brake: Disabled
  • Electronic Timing: Medium timing
  • Battery Protection: High cutoff voltage protection
  • Aircraft: Helicopter 1 Soft Start, no governor mode
  • Throttle response speed: Quick speed
  • Battery eliminator circuit (BEC): 6.0V for receiver/servos

Although the ESC is pre-programmed from factory, do re-program it to make sure the settings are at the supposed values. It eliminates any issues that might be introduced during manufacturing or storage.

Higher BEC voltage will give the servos more torque and reaction time. For specific servos requiring 5.0V or 5.5V (e.g. Futaba), use a servo step down voltage regulator.

Battery

What makes a good battery pack good is the ability to hold voltage under load. When you start to fly aggresively, some battery pack will drop more voltage than other, resulting in bogging of head speed. A good battery pack will have minimal voltage drop during heavy load, resulting in more punch and consistent speed.

Deans Connector

There are two main types of battery connectors, Deans and JST. Bullet plugs are used between the motor and speed controller. The JST connector is known have a low amperage rating (10-15A) and after awhile the surface will oxidize, eventually resulting in more resistance and heat. It could in extreme cases cause flight problems or unexpected twitching during peak load (e.g. full throttle and pitch).

File:Helicopter deans connectors.jpg

Replacing the plug with Deans connectors will improve the contact surface area and thus rating (50-75A). They're also easier to connect and disconnect, compared to JST.

Charging

Charger

Bantam BC6 charger:

Helicopter bantam bc6.jpg Helicopter bantam bc6 setup.jpg

I found that the Bantam BC6 would fit my needs and provide the quality I like. There are a few clones based on this charger, showing the reputation the manufacturer has for making chargers (Hint: good). Bantam is a Korean company.

The Bantam BC6 can charge 3x 2S, 2x 3S, and 1x 6S batteries. Maximum power output is 5.0A. Maximum discharging is 0.5A (due to limited heat dissipation).

It's possible to hook the charger up to a computer to monitor and record the charging sessions. Bantam offers a suitable Serial-to-USB cable and software, but it's also possible to make your own cable and use an 3rd-party application called LogView.

Charging in series

If the charger supports charging 6S1 batteries it's possible to connect two 3S1 batteries in series and charge them both at the same time. The essential part is the connect the main leads together, normally via a Y-Deans cable. Then connect the individual balancing wires from both batteries to the chargers cell balancing outputs, e.g. from battery #1 connect balancing wires to 1-3 on the charger. Next, split the balancing wire 3 from the charger so that it connects to the last cell on battery #1 and first cell on battery #2. Lastly connect the remaining 4-6 balancing wires to the charger. Also, connect the main Deans cable the to separate positive/negative output on the charger.

Remember: Always triple check your setup. Dealing with LiPo and possible short-circuit could be dangerous.

Helicopter charge connect 3s1 in series.png

Part list:

  • 1x EAC120-1 Bantam E-STATION 8-pin cable for BC6/PB6
  • 1x AM-8022 CMAX Y Deans for series connection
  • 2x 3s Balancer Female Connector

LiPo

Always use a quality charger when dealing with LiPo batteries. The batteries pack a lot of energy and requires special attention.

A normal LiPo battery for helis run in series of 2 or 3 cells. Combining cells in series means higher voltage and greater discharge capacity. To charge a LiPo battery, a balancing charger is recommended to properly charge each cell individually. Similarly charging only via the main leads will cause the capacity be unevenly distributed across the cells and could cause damage to the battery and in extreme cases explosive fires.

The continuous discharge capacity of a battery is specified in 'C's, where 1C is equal the capacity of the battery, e.g. a TP 910 mAh 11.1v 20C LiPo battery can handle a discharge of 20C * 860 mA, 17200 mA or 17.2 A continuous. Some batteries also specify the peak, or burst, discharge capacity, e.g 40C, but this is only for short periods of time.

Helicopter thunderpower 910mah.jpg Helicopter thunderpower 860mah.jpg

When charging a LiPo, most batteries can only be charged at 1C or less, e.g 910 mAh, or 0.9 A and lower. Some batteries can also be fast charged but only when specified in the manual/label.

The voltage can be calculated by multiplying 3.7V by the number of cells, e.g. 2 series equals 7.4V or 3 series equals 11.1V. Some chargers can detect if the wrong voltage/series is picked before starting the charging.

If the voltage of any individual cell is under 3.0V, the battery is considered dead and should not be attempted to be charged. The battery might be rescued by doing short burst to pump the voltage up and slowly charge it at 0.1 A.

Always remember to disconnect the battery from the heli once done, else the servos will drain the remaining power and damage/weaken the battery cells.

Best practice:

  • Charge at 1C or less, where 1C is the capacity of the battery, e.g. charge at 0.8 for a 800 mAh LiPo battery
  • Use a good balancing charger, once all the cells are exactly 4.20V, the current flow should stop
  • Disconnect the battery charging leads before unplugging the leads from the charger, prevents shorts
  • Use a LiPo safety bag and never leave the room during the charging process

References:

NiMH

Nickel Metal Hydride batteries has to be charged slowly and normally doesn't have balancing between cells. Current is forced through the battery and the voltage can fluctuate, thus cannot be used to determine when a battery is full. A NiMH battery be properly charged by setting a timer or temperature sensor.

A normal NiMH charger will put C/10 Amps of current into the battery, e.g. a 1500 mAh (1C) battery will be charged at maximum 150 mA (0.15A) for 15 hours. Modern cells have an oxygen recycling catalyst which prevents damage on overcharge, but this circuit can only keep up if the charge rate is C/10. This method does not require an end-of-charge sensor or timer, although it's good practice to use one.

When a battery is full or begin to overcharge the voltage will drop slightly, a good charger can detect this change and stop the flow of current. The temperature will also increase, which is another method to detect full charge.

Memory effect can occur when a battery is repeatedly only partially discharged. The maximum capacity will decrease, but can be reversed by cycling the battery (discharge-charge). The discharge voltage should not be under 1.0V, e.g. a 8 AA cell 9.6V battery should not drop lower than 8.0V. Use this method to determine discharge voltage to cycle a battery.

Best practices:

  • Charge at C/10 Amps, e.g. 1000 mAh (1C) NiMH battery should be charge at 0.1A for 10 hours, fully charged cell voltage is around 1.4V
  • Cycling could be done by discharging at light load 0.5A down to 1.0V per cell, e.g. 8.0V for a 8 cell 9.6V battery, then charged at normal C/10 rate
  • Use a proper charger with either a timer, temperature sensor, or end-voltage sensitivity sensor.

References:

Final Setup

Photo gallery of the final T-Rex 250 build with everything mounted.