Turnigy Tek Sumo
From ivc wiki
Jump to navigationJump to search
Similar/same models
- 2DogRC Techone 35-inch Popwing http://www.techonehobby.com/proview.asp?id=300 - RCGroups review
- Scrath Tek Sumo build [1]
Specifications
- Wingspan: 900 mm
- Center of gravity: 200-212 mm (manual) - max. range 190-212 mm
- Weight kit only: 230 grams (wing, winglets, motor mount, servo mount, push rods, carbon fiber rods, front padding)
Stock kit
- 1x Tek Sumo wing 2 halves
- 2x Pre-glued carbon fiber rods 2 mm on bottom wings
- 2x Pre-glued carbon fiber rods 3 mm on bottom elevons
- 2x Winglets
- 1x Front EPP padding block
- 2x Push rods 1 x 200 mm
- 3x Carbon fiber rods 2x 160 mm
- 1x Fiberglass reinforced tape 15 mm
- 1x Plywood motor mount 38 x 38 mm backplate 23 x 23 mm pattern
- 2x Plywood servo mount 23 x 12 mm
- 1x Plywood velcro battery mount 71.5 x 25 mm
- 2x Glassfiber control arm 21 mm
- 2x Linkage stopper 1.5 x 6 mm
- 4x Equipment bay plastic bands 250 mm
- 1x Instruction manual 4 pages
Setup weight
- 350 grams - setup 2208 1370 Kv, 20A ESC, 3S 1200 mAh, 6x5 [2]
- 489 grams - setup 2818 1350 Kv, 18A ESC, 3S 1800 mAh, 7x4 [3]
Tips and tricks
- To glue the wing halves together and motor mount, use PU (Polyurethane) glue, e.g. Gorilla Glue, keep pressed together for a while
- For attaching the winglets use hot glue in the main contact surfaces and silicone glue (Goop) around the bead [4] [5]
- Add new 4x50mm carbon fiber rods to the underside near the center of gravity point and also to the wings as spars for strength, use thick super glue and kicker
- Use servo cable extensions to reach the servos from the equipment bay
- Calculate the motor and propeller size for the desired air speed, flight time and efficency, use eCalc
- Insert glass fiber rods into the leading winge edge for better dent resistance on crashes, use superglue and glass reinforced tape to cover the groove
- Make incisions to remove the floor in the equipment bays and use glue+tape to re-attach the floor on the opposite side
- Put the equipments on the other side, top side, use tip above
- Relocate the servo holes to be perpendicular to the forward motion direction of the wing
- Detach the elevons using a razorblade and reattach using strong 3M Mailing and Storage tape for optimal free motion
- Reinforce the front tip of the wing with 2 x 110 mm carbon fiber rod insert
- Use glass fiber reinforced tape to cover servo wire trails
- Scorpion, Hacker, Cobra are all reported to be very good motors if you want better quality [6]
- To fine adjust the CoG, center of gravity, use the battery and motor as weight, pick a suitable combination, simple rule is motor weight / 0.025 ~= battery cap+-100 mAh, battery cap * 0.025 ~= motor weight+-5g
- Center of gravity point is 190 to 212 mm from the front of the nose, depending on battery and total weight
Setups
Guide:
- Optimal power around 200-300W [7]
- Calc http://flbeagle.rchomepage.com/software/webocalc_1.5.2/html/webocalc_metric.html
- Propeller rule [8]:
- Bigger prop = lower Kv motor, less amps, more thrust/climb
- Smaller prop = higher Kv motor, more amps, less thrust/climb, more pitch speed
Common setups:
- Docile/easy: Motor 1350 Kv D28xL19mm 40g, APC 7x4, 3S 1000mAh 83g [9]
- Cruising/easy: Motor 1450 Kv D28xL22mm 38g, APC 8x6, 3S 2200 mAh 170g [10]
- Cruising/FPV: Motor 1800 Kv D28xL22mm 38g, APC 7x4, 3S 1800 mAh 153g, 15-20 min flight [11]
- Cruising/FPV: Motor 1400 Kv D28xL26mm) 50g, APC 8x4, 3S 1500 mAh 138g, 15-20 min flight [12]
- Performance/long: Motor 1600 Kv D31xL31mm 63g, APC 7x6/8x4, 3S 2200 mAh 138g [13]
- Performance/speed: Motor 2200 Kv D28xL26mm 50g, APC 6x4, 3S 1500 mAh 138g, 10 min flight [14]
- Ultra/long: Motor 1400 Kv D35xL32mm 88g, APC 8x8, 2x 3S 2200 mAh 340g, 18-25 min flight [15]
- Ultra/fast: Motor 3200 Kv D28xL38m) 72g, APC 7x6, 3S 2200 mAh 170g [16]
Motor alternatives
Scorpion, Hacker, Cobra offer quality motors, but the priority here is low cost.
- HK2824-1300 HobbyKing 2824 1300Kv Brushless Outrunner 52g [17]
- L2205-1350 Turnigy L2205-1350 1350Kv Brushless Motor 30g, pair with 1300 mAh [18]
- RCTimer BC2826-10 1400KV Outrunner Brushless Motor, 50g [19]
- D2822/14 Brushless Outrunner 1450kv 38g, pair with 1500 mAh [20] [21]
- Tower Pro 2409-12t 1600kv 63g, heavy [22] [23]
- RCTimer A2208-12 1800KV Outrunner Brushless Motor 38g, pair with 1800 mAh [24]
- RCTimer BC2826-6 2200KV Outrunner Brushless Motor 50g, pair with 2200 mAh [25] [26]
- Turnigy NTM Prop Drive Series 35-30A 1400kv Brushless Outrunner [27]
- Turnigy 2836 Brushless EDF Motor 3200kv 72g [28]
Common propeller sizes:
- 6x4, 7x3, 7x5, 7x6, 8x4, 8x8
Build guides
- Flitetest Tek Sumo and Bonsai review
- bluegsxr6 Tek Sumo setup
- PaulT Tek Sumo build
- yarg Tek Sumo configuration suggestions
- octane81 Tek Sumo build [29]
- FPV Tek Sumo high speed mountain flyer [30]
- planex Tek Sumo setup
- FPV Sweden Tek Sumo build log
- XJet Tek Sumo RC plane of the week
- Rellik Demanon Tek Sumo setup
- beemerdon homemade balancing stand
