Difference between revisions of "Domekt Komfovent C4 Plus Modbus Registers"
Line 175: | Line 175: | ||
| 0x00..0x7F [b0-b7, 0..1]<br>Ex. 0x40=>64=>01000000<br>b1=1, supply sensor B1 fault | | 0x00..0x7F [b0-b7, 0..1]<br>Ex. 0x40=>64=>01000000<br>b1=1, supply sensor B1 fault | ||
| Alarm status (stop flags) | | Alarm status (stop flags) | ||
| b1-Supply sensor B1, <br>b2-Heater overheating, <br>b3-Water temp. low, <br>b4-Rotor stop, <br>b5-Frost possibility, <br>b6-Air temp. high, <br>b7-Air temp. low | | b1-Supply sensor B1, <br>b2-Heater overheating, <br>b3-Water temp. low, <br>b4-Rotor stop, <br>b5-Frost possibility, <br>b6-Air temp. high, <br>b7-Air temp. low <br>(1-Fault, 0-None) | ||
|- | |- | ||
| 1009 | | 1009 |
Revision as of 10:49, 12 July 2023
Domekt Komfovent C4 is a AHU (Air Handling Unit) for use in a HVAC system. The C4 is an older standard use from approx. 2011 to 2016.
Connection
Connect the unit to a computer using the provided RS485/ModBus cable extruding from the top. There is no need to add 820 Ohm 5V pull-up/gnd pull-down or 120 Ohm termination. It works fine as is.
The pin-out is as the following:
RJ-45 flat cable | Wire color | Function |
---|---|---|
Pin 1 | Color | Not used |
Pin 2 | Color | Not used |
Pin 3 | Red | +24VDC |
Pin 4 | Yellow | RS485 A+ |
Pin 5 | Green | RS485 B- |
Pin 6 | White | Gnd |
Pin 7 | Color | Not used |
Pin 8 | Color | Not used |
Modbus settings
To establish a working connection, it's important to match the following connection parameters. A single wrong setting will make the connection not work at all.
Bits per second/baudrate | 19200 |
Data bits/word length | 8 |
Parity | Even |
Stop bits | 1 |
It is also important to use the correct Modbus ID. It's the identifier on the bus and has to be correct in order for communication to happen with the AHU.
The C4 unit has a different Modbus ID than later models, so make sure to double check. Either of the following will work with only one unit on the Modbus line.
Modbus ID | 20 (specific identification address) | 254 (common identification address) |
Register list
The C4 unit uses the following Modbus data register functions to read and write data.
A CR2032 battery keeps the registers concurrent when the unit is unplugged, ex. the time and date.
Read data: | Function code 03 | Operation status, temperatures, fans speed, and etc. |
Write data single register: | Function code 06 | Turn on/off unit, set temperature, change auto/manual mode |
Write data multiple registers: | Function code 16 | Set values with decimals/floating integers |
Controller registers available on the C4 unit.
General settings and status
Modbus register | Type | Access | Range | Description | Data values |
1000 | Read/write | Integer | 0..1 | C4 Start/stop unit | 1-Start, 0-Stop |
1001 | Read/write | Integer | 0..1 | Season, heating enabled or prohibited | 1-Winter, 0-Summer |
1002 | Read/write | 2x Char | 0x0000..0x2359 | Time, hh:mm | Ex. 8:05 => 0x0805 |
1003 | Read/write | Integer | 1-7 | Day of the week | 1-Mon, 2-Tue, 3-Wed, 4-Thu, 5-Fri, 6-Sat, 7-Sun |
1004 | Read/write | 2x Char | 0x0101..0x1231 | Month-day date | Ex. 9th May => 0x0509 |
1005 | Read/write | Integer | 1900-2100 | Year date | Ex. 2023 |
1006 | Read/write | Integer | 1..100 | Modbus ID, default 20 | Ex. 20 |
1007 | Read | Integer | 11..14 | Alarm status (warnings) | 14-Service, 13-Heater off, 11-Rotor stop |
1008 | Read | Binary | 0x00..0x7F [b0-b7, 0..1] Ex. 0x40=>64=>01000000 b1=1, supply sensor B1 fault |
Alarm status (stop flags) | b1-Supply sensor B1, b2-Heater overheating, b3-Water temp. low, b4-Rotor stop, b5-Frost possibility, b6-Air temp. high, b7-Air temp. low (1-Fault, 0-None) |
1009 | Read | Integer | 3..28 | Alarm status (stop code) | 3-Rotor stop, 4-Heater overheating, 9-Supply sensor B1, 19-Air temp. low, 20-Air temp. high, 27-Water temp. low, 28-Frost possibility |
1010 | Read | Integer | 0..100 | Recuperation level (heat exchanger) | 0 to 100% |
1011 | Read | Integer | 0..100 | Electric heater level (heating element) | 0 to 100% |
1012 | Read | Integer | 0..100 | Water heating level (external) | 0 to 100% |
1013 | Read | Integer | 0..100 | Water cooling level (external) | 0 to 100% |
Ventilation settings and status
Modbus register | Type | Access | Range | Description | Data values |
1100 | Read/write | Integer | 1..3 | Ventilation level (manual mode) | 1-Low fan speed, 2-Normal fan speed (recommended), 3-High fan speed |
1101 | Read | Integer | 0..4 | Ventilation level (current operation) | 0-Off, 1-Low fan speed, 2-Normal fan speed, 3-High fan speed, 4-Override mode |
1102 | Read/write | Integer | 0..1 | Mode (Auto/Manual) | 0-Manual (preset fan speed), 1-Auto (schedule) |
1103 | Read/write | Integer | 20..100 / 0 | Intake ventilation intensity level 1 (EC-type fan) | 20 to 100% (EC-fan only) |
1104 | Read/write | Integer | 20..100 / 0..2 | Intake ventilation intensity level 2 (EC-type fan / AC-type fan) | 20 to 100% (EC-fan), 0 to 2 (AC-fan) |
1105 | Read/write | Integer | 20..100 / 0 | Intake ventilation intensity level 3 (EC-type fan) | 20 to 100% (EC-fan only) |
1106 | Read/write | Integer | 20..100 / 0 | Intake ventilation intensity level 4 (EC-type fan) | 20 to 100% (EC-fan only) |
1107 | Read/write | Integer | 20..100 / 0 | Exhaust ventilation intensity level 1 (EC-type fan) | 20 to 100% (EC-fan only) |
1108 | Read/write | Integer | 20..100 / 0..2 | Exhaust ventilation intensity level 2 (EC-type fan / AC-type fan) | 20 to 100% (EC-fan), 0 to 2 (AC-fan) |
1109 | Read/write | Integer | 20..100 / 0 | Exhaust ventilation intensity level 3 (EC-type fan) | 20 to 100% (EC-fan only) |
1110 | Read/write | Integer | 20..100 / 0 | Exhaust ventilation intensity level 4 (EC-type fan) | 20 to 100% (EC-fan only) |
1111 | Read/write | Integer | 0..1 | Override/"OVR"-mode | 0-Disable, 1-Enable |
1112 | Read/write | Integer | 1..90 | Override mode timer | 1 to 90 minutes |
1113 | Read | Integer | 0..90 | Override mode timer (current count down) | 0 to 90 minutes |
1114 | Read | Binary | 0..1 | AHU / Air Handling Unit fans status | 0-Stopped, 1-Operating |
1115 | Read | Integer | 0..100 | Supply fan level (current level) | 0 to 100% |
1116 | Read | Integer | 0..100 | Exhaust fan level (current level) | 0 to 100% |
Temperature settings and status
Modbus register | Type | Access | Range | Description | Data values |
1200 | Read | Integer | -300..750 | Supply air temperature, C (to rooms) | -30 to 75C, 10x C, ex. 250 => 25.0C |
1201 | Read/write | Integer | 0..300 | Setpoint temperature, C (for calculation of recuperation, heating levels) | 0 to 30C, 10x C, ex. 25.0C => 250 |
1202 | Read/write | Integer | 0..300 | Temperature correction, C (time based) | -90 to +90C, 10x C, ex. +4.5C => 45 |
1203 | Read/write | 2x Char | 0x0000..0x2359 | Temperature correction start time | Ex. 08:05 => 0x0805 |
1204 | Read/write | 2x Char | 0x0000..0x2359 | Temperature correction end time | Ex. 15:05 => 0x1505 |
1205 | Read | Integer | -100..1100 | Water temperature, C | -10 to 110C, 10x C, ex. 320 => 32.0C |
Temperature settings and status
Modbus register | Type | Access | Range | Description | Data values |
1200 | Read | Integer | -300..750 | Supply air temperature, C (to rooms) | -30 to 75C, 10x C, ex. 250 => 25.0C |
1201 | Read/write | Integer | 0..300 | Setpoint temperature, C (to set recuperation, heating levels) | 0 to 30C, 10x C, ex. 25.0C => 250 |
1202 | Read/write | Integer | 0..300 | Temperature correction, C (time based) | -90 to +90C, 10x C, ex. +4.5C => 45 |
1203 | Read/write | 2x Char | 0x0000..0x2359 | Temperature correction start time | Ex. 08:05 => 0x0805 |
1204 | Read/write | 2x Char | 0x0000..0x2359 | Temperature correction end time | Ex. 15:05 => 0x1505 |
1205 | Read | Integer | -100..1100 | Water temperature, C | -10 to 110C, 10x C, ex. 320 => 32.0C |
Schedule settings
Modbus register | Type | Access | Range | Description | Data values |
1300 | Read/write | 2x Char | 0x0000..0x2359 | Mon1 start time | Ex. 08:05 => 0x0805 |
1301 | Read/write | 2x Char | 0x0000..0x2359 | Mon1 stop time | Ex. 15:05 => 0x1505 |
1302 | Read/write | 2x Char | 0x0000..0x2359 | Mon2 start time | Ex. 08:05 => 0x0805 |
1303 | Read/write | 2x Char | 0x0000..0x2359 | Mon2 stop time | Ex. 15:05 => 0x1505 |
1304 | Read/write | 2x Char | 0x0000..0x2359 | Mon3 start time | Ex. 08:05 => 0x0805 |
1305 | Read/write | 2x Char | 0x0000..0x2359 | Mon3 stop time | Ex. 15:05 => 0x1505 |
1306 | Read/write | 2x Char | 0x0000..0x2359 | Tue1 start time | Ex. 08:05 => 0x0805 |
1307 | Read/write | 2x Char | 0x0000..0x2359 | Tue1 stop time | Ex. 15:05 => 0x1505 |
1308 | Read/write | 2x Char | 0x0000..0x2359 | Tue2 start time | Ex. 08:05 => 0x0805 |
1309 | Read/write | 2x Char | 0x0000..0x2359 | Tue2 stop time | Ex. 15:05 => 0x1505 |
1310 | Read/write | 2x Char | 0x0000..0x2359 | Tue3 start time | Ex. 08:05 => 0x0805 |
1311 | Read/write | 2x Char | 0x0000..0x2359 | Tue3 stop time | Ex. 15:05 => 0x1505 |
1312 | Read/write | 2x Char | 0x0000..0x2359 | Wed1 start time | Ex. 08:05 => 0x0805 |
1313 | Read/write | 2x Char | 0x0000..0x2359 | Wed1 stop time | Ex. 15:05 => 0x1505 |
1314 | Read/write | 2x Char | 0x0000..0x2359 | Wed2 start time | Ex. 08:05 => 0x0805 |
1315 | Read/write | 2x Char | 0x0000..0x2359 | Wed2 stop time | Ex. 15:05 => 0x1505 |
1316 | Read/write | 2x Char | 0x0000..0x2359 | Wed3 start time | Ex. 08:05 => 0x0805 |
1317 | Read/write | 2x Char | 0x0000..0x2359 | Wed3 stop time | Ex. 15:05 => 0x1505 |
1318 | Read/write | 2x Char | 0x0000..0x2359 | Thu1 start time | Ex. 08:05 => 0x0805 |
1319 | Read/write | 2x Char | 0x0000..0x2359 | Thu1 stop time | Ex. 15:05 => 0x1505 |
1320 | Read/write | 2x Char | 0x0000..0x2359 | Thu2 start time | Ex. 08:05 => 0x0805 |
1321 | Read/write | 2x Char | 0x0000..0x2359 | Thu2 stop time | Ex. 15:05 => 0x1505 |
1322 | Read/write | 2x Char | 0x0000..0x2359 | Thu3 start time | Ex. 08:05 => 0x0805 |
1323 | Read/write | 2x Char | 0x0000..0x2359 | Thu3 stop time | Ex. 15:05 => 0x1505 |
1324 | Read/write | 2x Char | 0x0000..0x2359 | Fri1 start time | Ex. 08:05 => 0x0805 |
1325 | Read/write | 2x Char | 0x0000..0x2359 | Fri1 stop time | Ex. 15:05 => 0x1505 |
1326 | Read/write | 2x Char | 0x0000..0x2359 | Fri2 start time | Ex. 08:05 => 0x0805 |
1327 | Read/write | 2x Char | 0x0000..0x2359 | Fri2 stop time | Ex. 15:05 => 0x1505 |
1328 | Read/write | 2x Char | 0x0000..0x2359 | Fri3 start time | Ex. 08:05 => 0x0805 |
1329 | Read/write | 2x Char | 0x0000..0x2359 | Fri3 stop time | Ex. 15:05 => 0x1505 |
1330 | Read/write | 2x Char | 0x0000..0x2359 | Sat1 start time | Ex. 08:05 => 0x0805 |
1331 | Read/write | 2x Char | 0x0000..0x2359 | Sat1 stop time | Ex. 15:05 => 0x1505 |
1332 | Read/write | 2x Char | 0x0000..0x2359 | Sat2 start time | Ex. 08:05 => 0x0805 |
1333 | Read/write | 2x Char | 0x0000..0x2359 | Sat2 stop time | Ex. 15:05 => 0x1505 |
1334 | Read/write | 2x Char | 0x0000..0x2359 | Sat3 start time | Ex. 08:05 => 0x0805 |
1335 | Read/write | 2x Char | 0x0000..0x2359 | Sat3 stop time | Ex. 15:05 => 0x1505 |
1336 | Read/write | 2x Char | 0x0000..0x2359 | Sun1 start time | Ex. 08:05 => 0x0805 |
1337 | Read/write | 2x Char | 0x0000..0x2359 | Sun1 stop time | Ex. 15:05 => 0x1505 |
1338 | Read/write | 2x Char | 0x0000..0x2359 | Sun2 start time | Ex. 08:05 => 0x0805 |
1339 | Read/write | 2x Char | 0x0000..0x2359 | Sun2 stop time | Ex. 15:05 => 0x1505 |
1340 | Read/write | 2x Char | 0x0000..0x2359 | Sun3 start time | Ex. 08:05 => 0x0805 |
1341 | Read/write | 2x Char | 0x0000..0x2359 | Sun3 stop time | Ex. 15:05 => 0x1505 |
1342 | Read/write | Integer | 0..3 | Mon1 ventilation level (fan speed) | 0-Off, 1-Low, 2-Normal, 3-Max. |
1343 | Read/write | Integer | 0..3 | Mon2 ventilation level (fan speed) | 0 to 3 |
1344 | Read/write | Integer | 0..3 | Mon3 ventilation level (fan speed) | 0 to 3 |
1345 | Read/write | Integer | 0..3 | Tue1 ventilation level (fan speed) | 0-Off, 1-Low, 2-Normal, 3-Max. |
1346 | Read/write | Integer | 0..3 | Tue2 ventilation level (fan speed) | 0 to 3 |
1347 | Read/write | Integer | 0..3 | Tue3 ventilation level (fan speed) | 0 to 3 |
1348 | Read/write | Integer | 0..3 | Wed1 ventilation level (fan speed) | 0-Off, 1-Low, 2-Normal, 3-Max. |
1349 | Read/write | Integer | 0..3 | Wed2 ventilation level (fan speed) | 0 to 3 |
1350 | Read/write | Integer | 0..3 | Wed3 ventilation level (fan speed) | 0 to 3 |
1351 | Read/write | Integer | 0..3 | Thu1 ventilation level (fan speed) | 0-Off, 1-Low, 2-Normal, 3-Max. |
1352 | Read/write | Integer | 0..3 | Thu2 ventilation level (fan speed) | 0 to 3 |
1353 | Read/write | Integer | 0..3 | Thu3 ventilation level (fan speed) | 0 to 3 |
1354 | Read/write | Integer | 0..3 | Fri1 ventilation level (fan speed) | 0-Off, 1-Low, 2-Normal, 3-Max. |
1355 | Read/write | Integer | 0..3 | Fri2 ventilation level (fan speed) | 0 to 3 |
1356 | Read/write | Integer | 0..3 | Fri3 ventilation level (fan speed) | 0 to 3 |
1357 | Read/write | Integer | 0..3 | Sat1 ventilation level (fan speed) | 0-Off, 1-Low, 2-Normal, 3-Max. |
1358 | Read/write | Integer | 0..3 | Sat2 ventilation level (fan speed) | 0 to 3 |
1359 | Read/write | Integer | 0..3 | Sat3 ventilation level (fan speed) | 0 to 3 |
1360 | Read/write | Integer | 0..3 | Sun1 ventilation level (fan speed) | 0-Off, 1-Low, 2-Normal, 3-Max. |
1361 | Read/write | Integer | 0..3 | Sun2 ventilation level (fan speed) | 0 to 3 |
1362 | Read/write | Integer | 0..3 | Sun3 ventilation level (fan speed) | 0 to 3 |