T-Rex 250 Setup

This shows the setup of my T-Rex 250 and the experience I've had learning and experimenting with the build. Please visit RC Heli Wiki for an excellent resource regarding helicopter terms and concepts.

Follow this guide to-to-bottom, get a good mechanical setup before setting up the electronics. A great companion is Bob White a.k.a Finless' videos.

• Back to mail helicopter page

Prequesite

On the radio create a new profile for the helicopter and reset all de settings. Follow the manual to setup the basic build.

Head

The head setup should mechanically be as symmetrical and zero-pitched as possible. The radio should be set to have a straight throttle curve in normal mode before starting the adjustments.

Install the servos and mount a suitable servo arm 90 degrees to the swashplate. Connect the rods to the swashplate with the length specified in the manual. Note that the following method to change the direction of the servo is only used on the throttle/pitch, for elevator, aileron, and rudder is reversed using swash mixing. Move the throttle stick slightly up and watch the servos, all three should move collectively up to raise the swashplate, if not, go into the radio setup and reverse the direction of the affected servo.

The head is split up in 3 levels (top-to-bottom); Bell-Hiller mixer level, washout arms level, and swashplate level (look at the picture below). On zero-pitch the Bell-Hiller and washout is level. That's determined by the lengths of the link-rods connecting the levels. The washout arms level should be in the middle positioned between minimum and maximum pitch while the arms remain level.

Once they're level, remove the rotor head and use a swashplate leveling tool on top of the swashplate and adjust the length of the pushrods to perfectly level the swashplate. The leveling tool fits on top of the swashplate and will reveal any gaps on either side of the 3 servo-links. [FIXMELATER]

If everything seem level, use a digital caliper verify and duplicate the length of related link rods. This will reduce vibrations and tracking issues even more.

Tail

Setup:

• 5 mm from servo center

Gyro

GP750 settings:

• Pulse frame: 1520us
• Servo type: DS (Digital Servo)
• Direction: Rev (mounted up-side-down)
• Servo travel: Limit set with no binding
• Heli type: Small heli
• Delay: 0 delay

The gyro is a device connected between the receiver and the rudder servo, it will stabilize the tail by counter the torque reaction of the main rotor. There are two types, head hold mode continuously tries to hold the tip of the helicopter at a constant angle, while the other mode, rate mode, dampens any external push to the tail. The former is preferred for normal hovering and acrobatics, while the second is mostly used for scale models.

• RC Heli Wiki Gyro
• Mini-HowTo - Align GP-750 Heading Lock Gyro

ESC

The default configuration:

• Soft start
• 6v BEC to receiver/servos

Although the ESC is pre-programmed from factory, re-program it to make sure the throttle range matches the transmitter stick range. It also fixes any issues that might be introduced during manufacturing or storage.

Battery

What makes a good battery pack good is the ability to hold voltage under load. When you start to fly aggresively, some battery pack will drop more voltage than other, resulting in bogging of head speed. A good battery pack will have minimal voltage drop during heavy load, resulting in more punch and consistent speed.

Receiver

AR6100e receiver setup (receiver - device):

• THRO - ESC
• AILE - Right cyclic servo
• ELE - Rear cyclic servo
• RUD - Gyro (3-wires plug)
• GEAR - Gyro (1 wire plug - gain)
• AUX1 - Left cyclic servo

Other receivers wil have different layout. Also, the channels can be moved to a different channel on most transmitters.

• DX7 and AR6100 setup

Radio

Pitch/Throttle curves / Dual Rates

A good radio normally has a dual-rate switch on to of the radio for Normal Mode (hovering), Stunt Mode #1 (3D), and Stunt Mode #2 (more power 3D). Stunt mode is also referred to as IdleUp 1 and IdleUp 2. Another mode is Throttle Hold for auto-rotation on engine failure, a second switch is normally used for this.

Normal Mode is used during spin-up and hovering. With the stick down the engine will be off and with 70% up the helicopter should be hovering. These parameters are mainly set-up on the radio by altering the engine throttle and rotor pitch curve.

With Stunt Mode turned on the hovering mode is turned into a flexible mode where the helicopter can be flown up-side-down. Essentially the Normal Mode above 50% is mirrored to the 0-49% section of the stick, but with a negative rotor pitch instead. Look at the picture below to understand the difference between Normal and Stunt.

While setting up the curves, there is an option to enable "Exponential". Expo smoothens the curve and stick input will have a finer feel, not that rough, requires more stick movement to get the right input. But it's not recommended to keep expo on as it removes some of the real feel of the helicopter and can hinder progression.

File:Helicopter stuntmode throttle.png File:Helicopter stuntmode pitch.png

The throttle curve dips on the middle because the pitch is close to 0 degrees, thus requiring less power. Higher pitch requires more engine power to keep the head speed constant.

Collective Cyclive Pitch Mixing

CCPM Setup:

• 3 servo
• 120° degrees apart
• Swash mix (aileron, elevation, pitch): 40-45% (larger values might cause binding)
• Maximum/Minimum pitch: 10.0° (max. 11.0°)

Also known as CCPM. This controls the pitch and movement of the rotor and flybar, thus throttle/pitch (up/down), aileron (left/right), and elevation (forward/backward).

It's called collective because there are 3 servos involved. There are two types of CCPM, mechanical bell crank and electronic mixing. The latter one is used on most helicopters today but requires precision servo setup and some radio configuration. The radio is set-up to mix the 3 servos in order to move the swash plate in the right direction and plane, be it up-down, left-right, or forward-backward.

Move the aileron and elevator stick, if the response is not as expected, e.g. move aileron left, swashplate should move left, go into the setup and swash mixing, change the positive percentage to negative (-).

• RC Heli Wiki CCPM Setup
• Bob White CCPM setup video

Gyro

• Gain: 70-75% (20-25% heading hold)

The gyro is connected to the receiver by two plugs. One for the rudder and one for gain. Gyro gain is measured in percentage and controls the gyro mode. The range 0-49% is called rate mode and the tail will not automatically bounce back to the original position if it has been pushed by an external force, but rather dampen the movement. While the upper 51-100% range is called heading hold mode and will try to keep the front of the helicopter at a constant angle/heading.

Notice that the gain wire is connected to a regular channel and if the channel is reversed so will the rates.

There are two ways to set gyro gain, via the gyro menu or set the channel end points (max/min. travel range). The former is preferred.