Difference between revisions of "LED Bandwidth Monitor"

From ivc wiki
Jump to navigationJump to search
 
(19 intermediate revisions by the same user not shown)
Line 1: Line 1:
[[Image:LED_Bandwidth_Monitor_assembly_dark.jpg|right|550px]]
[[Image:LED_Bandwidth_Monitor_assembly_dark.jpg|right|600px]]


After discovering how cool RGB LED strips are, I decided to make a bandwidth monitor for the Internet connection at our place. Since there are many users active on the same connection there's bound to be conflicts where someone is gaming and another is downloading, causing the ping to fluctuate (even with QoS HTB-init set up).
After discovering how cool RGB LED strips are, I decided to make a bandwidth monitor for the Internet connection at our place. Since there are many users active on the same connection there's bound to be conflicts where someone is gaming and another is downloading, causing the ping to fluctuate (even with QoS HTB-init set up).
Line 13: Line 13:


* [http://www.adafruit.com/index.php?main_page=product_info&cPath=37&products_id=306 Adafruit RGB LED Strip product page]
* [http://www.adafruit.com/index.php?main_page=product_info&cPath=37&products_id=306 Adafruit RGB LED Strip product page]
Pin-out for Arduino UNO:
* SI - pin 8 (set static high in code)
* DI - pin 11 (SPI data)
* CI - pin 13 (SPI clock)
* LI - pin 10 (latch pin toggled in code)


== Controlling LEDs ==
== Controlling LEDs ==
Line 19: Line 25:
The control IC is a HL1606 with two channels (A and B) each controlling one RGB LED, fading capability, driven by 5V, and has a SPI-like protocol.
The control IC is a HL1606 with two channels (A and B) each controlling one RGB LED, fading capability, driven by 5V, and has a SPI-like protocol.


* [http://beta.ivancover.com/led_bwmon/HL1606E.pdf HL1606 Datasheet chinese]
* [http://beta.ivancover.com/led_bwmon/HL1606S.pdf HL1606 Datasheet chinese]
* [http://beta.ivancover.com/led_bwmon/HL1606S.pdf HL1606 Datasheet english] - pinout wrong
* [http://beta.ivancover.com/led_bwmon/HL1606E.pdf HL1606 Datasheet english] - pinout wrong


The kind people over at Adafruit has updated/published two Arduino libraries, one plain primary only colors and one using PWM to create a huge color spectrum. The latter allows dimming of the three primary colors to display 3, 4, or 5-bit colors per LED.
The kind people over at Adafruit has updated/published two Arduino libraries, one plain primary only colors and one using PWM to create a huge color spectrum. The latter allows dimming of the three primary colors to display 3, 4, or 5-bit colors per LED.
Line 55: Line 61:
A simple GET-http request containing the values as parameters, e.g. http://192.168.233.177/?up=6&dn=30, is sent to a basic webserver listening on the first Arduino. Once the values are received by the microcontroller, they're parsed to integers and transferred over a I2C/TWI-bus to the second LED-driving Arduino.
A simple GET-http request containing the values as parameters, e.g. http://192.168.233.177/?up=6&dn=30, is sent to a basic webserver listening on the first Arduino. Once the values are received by the microcontroller, they're parsed to integers and transferred over a I2C/TWI-bus to the second LED-driving Arduino.


[[Image:LED_Bandwidth_Monitor_schematic.png|300px]]
[[Image:LED_Bandwidth_Monitor_schematic.png|400px]]


[[Image:LED_Bandwidth_Monitor_arduinos.jpg|300px]] [[Image:LED_Bandwidth_Monitor_arduinos_leds.jpg|300px]]
[[Image:LED_Bandwidth_Monitor_arduinos.jpg|300px]] [[Image:LED_Bandwidth_Monitor_arduinos_leds.jpg|300px]]
Line 64: Line 70:


Download the shell script:
Download the shell script:
* Download monitor update script
* [http://beta.ivancover.com/led_bwmon/bwmon-20100111.tgz Download Linux monitor update script] - Requires bwbar, screen, wget, and the usual Unix essentials


Download the Arduino source code:
Download the Arduino source code:


* Download Web Server Interface
* [http://beta.ivancover.com/led_bwmon/web_interface_rev3.zip Download Arduino Ethernet Web Server Interface] - 2012-01-01 rev3
* Download LED Driver - Requires the [https://github.com/adafruit/HL1606-LED-Strip-PWM HL1606-LED-Strip-PWM Arduino library] to be installed
* [http://beta.ivancover.com/led_bwmon/led_driver_rev3.zip Download Arduino LED Driver] - 2012-01-01 rev3 - Requires the [https://github.com/adafruit/HL1606-LED-Strip-PWM HL1606-LED-Strip-PWM LED-Strip-PWM library] to be installed (put in library folder)


== Power ==
== Power ==
Line 90: Line 96:


The only wires connected to the assembly is 5V power and an ethernet cable connected to a network-switch.
The only wires connected to the assembly is 5V power and an ethernet cable connected to a network-switch.
== Video ==
Shows the bandwidth meter in action. Shoot on a Nikon D5000, soundtrack "Caribou - Sun Altrice's 'Only What You Gave Me' Remix".
<html><object width="640" height="385"><param name="movie" value="http://www.youtube-nocookie.com/v/oOapRE5BkuI?fs=1&amp;hl=en_US&amp;rel=0"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube-nocookie.com/v/oOapRE5BkuI?fs=1&amp;hl=en_US&amp;rel=0" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="640" height="385"></embed></object></html>


== Upgrades ==
== Upgrades ==
Line 106: Line 117:
* [http://www.arcfn.com/2009/07/secrets-of-arduino-pwm.html Secrets of Arduino PWM]
* [http://www.arcfn.com/2009/07/secrets-of-arduino-pwm.html Secrets of Arduino PWM]
* [http://jimsmindtank.com/atmega168-and-master-spi/ ATmega168 and master SPI]
* [http://jimsmindtank.com/atmega168-and-master-spi/ ATmega168 and master SPI]
* [http://www.ladyada.net/products/digitalrgbledstrip/index.html LadyAda proper Digital RGB LED strip tutorial]

Latest revision as of 00:32, 22 December 2012

LED Bandwidth Monitor assembly dark.jpg

After discovering how cool RGB LED strips are, I decided to make a bandwidth monitor for the Internet connection at our place. Since there are many users active on the same connection there's bound to be conflicts where someone is gaming and another is downloading, causing the ping to fluctuate (even with QoS HTB-init set up).

I discovered the strips over at the Adafruit blog, check this Adafruit Ask an Engineer video (starting at 3:23) for details.

LED Strips

LED Bandwidth Monitor strip.jpg

One meter of LED strip has 32 LEDs, where each section is 2.5 inch (6.35 cm) and consists of one shift-register IC, controlling two LEDS. There is also a bypass capacitor for the IC and current-limiting resistors for the LEDs. Each RGB LED has 6 pins, grouped in pairs for each of the 3 primary colors, this allows resistors to be connected fore or aft. One reel is 5 meters and comes with end-connectors already soldered on.

The strip is housed in a rubber casing and when the ends are sealed can be made semi-waterproof.

Pin-out for Arduino UNO:

  • SI - pin 8 (set static high in code)
  • DI - pin 11 (SPI data)
  • CI - pin 13 (SPI clock)
  • LI - pin 10 (latch pin toggled in code)

Controlling LEDs

LED Bandwidth Monitor hl1606.png

The control IC is a HL1606 with two channels (A and B) each controlling one RGB LED, fading capability, driven by 5V, and has a SPI-like protocol.

The kind people over at Adafruit has updated/published two Arduino libraries, one plain primary only colors and one using PWM to create a huge color spectrum. The latter allows dimming of the three primary colors to display 3, 4, or 5-bit colors per LED.

Shift-register updates are pushed down the strip in serial form (one clock cycle, one bit). A single update consists of 16-bit, where the first 8-bit is channel A and the least 8-bit channel B.

The data format for the 8-bit channels (datasheet):

   ________________________________________________________________________
  |   D1   |   D2   |   D3   |   D4   |   D5   |   D6   |   D7   |    D8   |
   ------------------------------------------------------------------------
        LED1 CMD         LED2 CMD          LED3 CMD         2X     LatchOK 

Each LED has 2-bit control, where 00 is off and 01 is on, the last two combinations are for fading (not used in PWM lib). The 2X fading-bit is not used here either. LatchOK, when pulled high, puts the content of the shift-register into the 'live' output buffers to control the LED.

To drive 128 LEDs without flickering due to low update frequency or spaz out due too slow shift-register reaction time (slew rate), the strip object is using:

  • 3-bit PWM per LED, results in 2^3=8 color resolution per LED (dimming single color)
    • For the full RGB LED (3 LEDs), this gives a total of 8^2=512 available colors
  • SPI clock is FCPU/32 -> 16MHz/32=500kHz

Processing time for one LED strip update: (128 LEDs * 8-bit per LED * 32 SPI-divider * 1000 ms) / 16 MHz = 2.048 ms. This means the update frequency is 1000/2.048 = 488 Hz. Which is pleny to avoid flickering and low enough for the HL1606 to keep up.

There is a lot of details on the HL1606 in the Arduino-lib examples by Adafruit.

Bandwidth Monitor

The data used to change the active display is feed from the network gateway using the bwbar utility for Linux. It runs as a daemon and outputs two text files every other second containing the current bandwidth utilization on the inbound and outbound interface. This text file is picked up by a shell script (sh), parsed, percentage of the maximum speed (9500kbit/s) is calculated and put in two variables. Last, the values are then passed over the network to an Arduino with an ethernet-shield using the wget utility.

bwbar -k -t 1 -d bwbar/ -f inbound.txt -p inbound.png --output eth1 1000
bwbar -k -t 1 -d bwbar/ -f outbound.txt -p outbound.png --output eth0 1000 
wget -O resp.txt http://192.168.233.177/?up=6&dn=30

A simple GET-http request containing the values as parameters, e.g. http://192.168.233.177/?up=6&dn=30, is sent to a basic webserver listening on the first Arduino. Once the values are received by the microcontroller, they're parsed to integers and transferred over a I2C/TWI-bus to the second LED-driving Arduino.

LED Bandwidth Monitor schematic.png

LED Bandwidth Monitor arduinos.jpg LED Bandwidth Monitor arduinos leds.jpg

The second Arduino is the LED-driver and is responsible for updating and driving the strip. It had to be on a separate device because the ethernet-shield requires SPI, as does the LED strip, and there's only one hardware SPI-interface. It might be possible to put everything on one device and address ethernet/strip when needed, but I decided it was too time consuming to look into at the moment. The update rate of the LED strip could also suffer (as the 3-bit colors are controlled by PWM and require processor cycles).

strip.setLEDcolorPWM(i, 0, 255*bright, 0); // parameters: LED-index, R, G, B color

Download the shell script:

Download the Arduino source code:

Power

A 5V 2.5A powersupply is powering the LEDs and the Arduinos. The maximum driving current for one 2.5-inch section is unknown, but the Adafruit product page states 120mA for 2 LEDs including the HL1606 (which seem a bit high to me).

I have yet to measure the actual current draw.

Mount

LED Bandwidth Monitor plexiglass assembly.jpg

I wanted to make the monitor bars to be huge and as long as possible to get satisfactory resolution. To fit the space on the wall, I ended on the final dimension of 2 meters long and 15 cm height. That's 2x64 LEDs for download and upload monitor bar, 100/64 = 1.6 LED per percentage-point.

To mount the LED strips, I first made a 2 meter long baseplate out of 10 pieces of 15x20 cm plexiglass plates glued together using regular CA-glue. Drilled holes for each 20 cm section, pulled fishing string through the holes, put double sided adhesive padding on the strip, and tighned the string to get a firm fit. Remember, the LED strips is hang vertically and gravity will pull the strips down over time so adhesive only will fail.

LED Bandwidth Monitor fishing string.jpg LED Bandwidth Monitor u connection.jpg

Using 4 hooks and double feed of fishing string, the entire plate with the two Arduino devices and LED strips was lifted into place. The assembly is hanging 8.5 cm away from the wall to give a cool effect.

LED Bandwidth Monitor assembly side.jpg LED Bandwidth Monitor assembly back.jpg

The only wires connected to the assembly is 5V power and an ethernet cable connected to a network-switch.

Video

Shows the bandwidth meter in action. Shoot on a Nikon D5000, soundtrack "Caribou - Sun Altrice's 'Only What You Gave Me' Remix".

Upgrades

Possible improvements:

  • Use UDP instead of initializing a HTTP connection every time to update
  • One Arduino instead of two
  • One cable, power-over-ethernet, might need to cut traces on ethernet-shield

References