Difference between revisions of "Eee PC Internal Upgrades"

From ivc wiki
Jump to navigationJump to search
Line 27: Line 27:
After cracking the case open, I stripped all the unnecessary parts from the circuit board like the LED and external power connector.
After cracking the case open, I stripped all the unnecessary parts from the circuit board like the LED and external power connector.


[[Image:Eee usbhub open.jpg|400px]]
[[Image:Eee usbhub box.jpg|400px]] [[Image:Eee usbhub open.jpg|400px]]


''Top:''
''Top and bottom:''


[[Image:Eee usbhub first top.jpg|400px]]
[[Image:Eee usbhub first top.jpg|400px]] [[Image:Eee usbhub first bottom.jpg|400px]]
 
''Bottom:''
 
[[Image:Eee usbhub first bottom.jpg|400px]]


For the position I chose to place the first hub directly under the touch pad, next to the memory slot. It fits nicely and the depth of the circuit board just right. It's placed in the middle of the Eee motherboard, allowing for short wires for the different peripherals.  
For the position I chose to place the first hub directly under the touch pad, next to the memory slot. It fits nicely and the depth of the circuit board just right. It's placed in the middle of the Eee motherboard, allowing for short wires for the different peripherals.  

Revision as of 01:25, 19 December 2007

USB hub

To install devices internally, more USB-connections are needed. I hooked into one of the regular USB-ports and routed the D+/D- signals from the southbridge/controller to a 4 port USB-hub. To make the port I hooked into work again, one of the 4 ports is connected back to the USB-port (Hub-to-USB-port and USB-port-to-HUB).

I installed 2 hubs this way to get enough ports and load balancing the bandwidth. Having two storage devices on the same upstream connection is not a good idea speed-wise when utilizing both at the same time.

The reason I choose to hook into the USB-port and leave the spare Mini-PCIe USB connection alone is that I want to:

  • Be able to use Mini-PCIe cards based on USB later
  • Disable the USB-ports in BIOS and disable all the new devices
  • Not have the devices disabled if I used the webcam or wifi connections

More information about USB hubs over at Wikipedia.

Models

For the type of hub, I went for a as small as I could find. The one I found had four rotating USB connections and one upstream connection sticking out from its side.

It goes under various names, here are a few I found:

There's also a model with integrated SD card reader. Mine uses a Genesys Logic GL850A chip.

Eee usbhub chip.jpg

Installation

After cracking the case open, I stripped all the unnecessary parts from the circuit board like the LED and external power connector.

Eee usbhub box.jpg Eee usbhub open.jpg

Top and bottom:

Eee usbhub first top.jpg Eee usbhub first bottom.jpg

For the position I chose to place the first hub directly under the touch pad, next to the memory slot. It fits nicely and the depth of the circuit board just right. It's placed in the middle of the Eee motherboard, allowing for short wires for the different peripherals.

Eee usbhub first.jpg

The second hub is positioned over the SSD NAND flash chips. The total height is still low enough that it's not touching the chassis.

Eee usbhub second.jpg

Eee usbhub height.jpg

I hooked into the data signals of one of the USB ports on the right-side. One of the ports on the hubs is used to hook up the USB port again.

Overview:

Eee usbhub port overview.jpg

Power is routed from one of the 5v points and through the switch board. Ground is connected to the nearest point.

GPS with antenna

Bluetooth

SDHC card reader

Flash drive

Power switch

  • Integrated: Webcam, Wifi PCIe adapter, SD card reader, Sound card, Atheros eithernet, Atheros Mini-PCIe adapter
  • USB hub: Bluetooth, SD card reader, GPS adapter, FM transmitter

Modem

The modem port on the Eee is stuffed with a piece of black foam and not used. The modem is not installed on any Eee machine but the internal connection points are still there. The modem card connected via a MDC v1.5 connection, and 12 pin header for the card and the 2 pin header to connect to the RJ-11 jack is still in place on all current 4G motherboards.

Asus is still providing the Windows driver for the Conexant 56K modem on their download site, look for Modem_XP.zip

The modem card can be found on various Dell, Acer, and Sony laptops. On Ebay the Conexant card can be found under these model numbers:

Wifi

The wifi-card on the Eee is only 802.11b/g, not the latest draft-N. The card is can be easily changed by removing two screws and unmounting the card from the Mini-PCI Express socket.

After searching around I found a Intel 4965agn 802.11a/b/g/n Mini-PCIe card for a decent price.

Since 802.11n is MIMO (Multiple Input Multiple Output) it requires 3 antennas for optimal performance and range. I had a dead Nintendo Wii which happens to use the same antenna connectors for it's Broadcom wireless-card. The connector type on the Intel card is Hirose U.FL-R-SMT and on the antenna U.FL-LP-066.

FM transmitter

Other Possible Internal Upgrades

  • USB relay power switch
  • New keyboard (non-taiwanese) [1]
  • FM transmitter
  • CPU/GPU/Chipset voltage mod
  • Silicon Motion NAND flash replacement
  • Modemport - Wifi antenna, additional ethernet port
  • Modemport as a switch - remove to turn off, plug in to power
  • Disable the fan to conserve power
  • USB touch-screen overlay
  • Copperplate with thermal tape better cooling

References